Publications Scientifiques

Permanent URI for this communityhttps://dspace.univ-boumerdes.dz/handle/123456789/10

Browse

Author: search.filters.author.Iachachene, FaridaSubject: search.filters.subject.Metal foam

Search Results

Now showing 1 - 3 of 3
  • No Thumbnail Available
    Item
    A comprehensive numerical study on melting performance in a storage cavity with partial metal foam integration: Design and economic assessment
    (Elsevier, 2024) Cheradi, Hanane; Haddad, Zoubida; Iachachene, Farida; Mansouri, Kacem; Arıcı, Müslüm
    Despite remarkable technological progress aimed at improving thermal performance of storage systems, designing cost-effective thermal storage solutions still remains a challenge. Consequently, to address this gap, the current study provides a detailed numerical analysis of the melting performance within a storage cavity with partial metal foam integration, considering both design and economic aspects. Five distinct designs were considered to provide a comprehensive assessment of the melting process including non-porous and porous designs. Various factors such as foam position, foam shape and foam filling ratio were examined under different criteria. The results revealed that designs employing kite-shaped, triangular-shaped, square-shaped, and trapezoidal-shaped foam under optimal location resulted in melting time reduction of 74.8 %, 67.0 %, 50.9 %, and 42.8 %, respectively, in comparison to the non-porous design. The findings highlight the kit-shaped foam as the optimal foam shape, with a notable 7.8 % difference in melting times between designs with kite and triangular foams, and an 8.1 % disparity between designs with square and trapezoidal foams. From an economic assessment, it was found that the kit-shaped foam filling design, with a 1/3 filling ratio, proved to be cost-effective when the unit price ratio of the metal foam to PCM fell within the range of 4 to 12. Interestingly, for ratios below 4, the same design, with a 1/2 filling ratio, emerged as an economical solution. This study contributes to the field by providing quantitative insights into the design and economic viability of metal foam integrated thermal storage systems.
  • No Thumbnail Available
    Item
    Numerical investigation and optimization of melting performance for thermal energy storage system partially filled with metal foam layer: New design configurations
    (Elsevier, 2023) Haddad, Zoubida; Iachachene, Farida; Sheremet, Mikhail A.; ;Abu-Nada, Eiyad
    Low thermal performance of storage systems represents a barrier to their industrial/engineering application and commercialization. Among all the proposed methods, combination of phase change material with metal foams appears more promising due to the high thermal conductivity of metal foams. However, the insertion of metal foams reduces the PCM volume; hence, a lower amount of stored energy. The present numerical study thoroughly addresses this issue with a focus on the optimization of melting performance for thermal energy storage system partially filled with metal foam layer. A finite volume method based on the enthalpy–porosity technique has been adopted for the numerical simulations. The metal foam location, porosity, and nanoparticle volume fraction were optimized to explore their effects on the melting performance. The results showed that inserting the foam layer diagonally from the top left to the right bottom leads to the lowest melting time. Compared to pure PCM, the melting time increases by 77.7%, while the stored energy decreases by 6.7%. The optimum porosity was found to be 0.88 as it gives approximately the same amount of stored energy as that of pure PCM with a deviation of 4%. Adding nanoparticles to pure PCM increases the melting rate by approximately 8%, while it decreases the stored energy by almost 3%. It is concluded that hybrid systems, i.e., metal foam at an optimum porosity and nanoparticles is more efficient than using each technique separately
  • No Thumbnail Available
    Item
    Natural convection melting of phase change material in corrugated porous cavities
    (Elsevier, 2022) Iachachene, Farida; Haddad, Zoubida; Abu-Nada, Eiyad; Sheremet, Mikhail A.
    In this paper, a numerical study is carried out to examine the melting inside a wavy cavity under partial heating. A wide range of numerical computations have been performed to understand the effect of porosity, pore density, wall waviness, and heater location and intensity on the melting process. The results revealed that lower metal foam porosity resulted in higher melting rate and lower thermal storage capacity. However, pore density indicated no effect on melting performance for porosity in the range 80–96 %. When considering heater location at various porosities, its impact on melting performance is small at low porosity but becomes significant at higher porosity. Top–bottom partial heating can save almost 10 % of the melting time at ɛ = 0.96. Moreover, the PCM can store more energy, i. e. 11.36 %, when the heater location was changed from center or top–bottom position to top or bottom position at ɛ = 0.96. The results further showed that increasing the number of undulations can save 27.4 % of the melting time at ε = 0.96. Therefore, it can be concluded that higher energy storage and melting rate can be achieved by increasing the number of undulations