Publications Internationales

Permanent URI for this collectionhttps://dspace.univ-boumerdes.dz/handle/123456789/13

Browse

Author: search.filters.author.Abu-Nada, Eiyad

Search Results

Now showing 1 - 3 of 3
  • No Thumbnail Available
    Item
    The effect of nano encapsulated phase change materials and nanoparticles on turbulent heat transport : a conical diffuser scenario
    (Elsevier, 2022) Iachachene, Farida; Haddad, Zoubida; Arıcı, Müslüm; Abu-Nada, Eiyad; Sheremet, Mikhail A.
    The present work investigates turbulent flow of single and hybrid nanofluids filled in a conical diffuser. The heat transfer coefficients and pressure losses are analyzed at various Reynolds numbers and nanoparticle volume fractions. The diffuser is filled with Al2O3, nano encapsulated phase change material NEPCM, and NEPCM_Al2O3 nanofluids. The thermophysical parameters of all nanofluids were determined using a novel methodology based on the thermodynamic equilibrium data for binary liquid mixtures. A notable novelty in the current work is the introduction of an innovative method of hybrid nanofluids composed of nanoparticles with and without phase change material (PCM). When compared to the other nanofluids tested, the NEPCM nanofluid presented the lowest pressure loss and the greatest heat transfer improvement within the diffuser. The Nusselt number of NEPCM nanofluids is enhanced by 15%, while for NEPCM_Al2O3 and Al2O3 nanofluids is increased by 10% and 6%, respectively. Similarly, the pressure drop is greater as compared to the base fluid, where the pressure drop is increased by 1%, 3.5%, and 5% for NEPCM, Al2O3, and NEPCM_Al2O3 nanofluid, respectively
  • No Thumbnail Available
    Item
    Natural convection melting of phase change material in corrugated porous cavities
    (Elsevier, 2022) Iachachene, Farida; Haddad, Zoubida; Abu-Nada, Eiyad; Sheremet, Mikhail A.
    In this paper, a numerical study is carried out to examine the melting inside a wavy cavity under partial heating. A wide range of numerical computations have been performed to understand the effect of porosity, pore density, wall waviness, and heater location and intensity on the melting process. The results revealed that lower metal foam porosity resulted in higher melting rate and lower thermal storage capacity. However, pore density indicated no effect on melting performance for porosity in the range 80–96 %. When considering heater location at various porosities, its impact on melting performance is small at low porosity but becomes significant at higher porosity. Top–bottom partial heating can save almost 10 % of the melting time at ɛ = 0.96. Moreover, the PCM can store more energy, i. e. 11.36 %, when the heater location was changed from center or top–bottom position to top or bottom position at ɛ = 0.96. The results further showed that increasing the number of undulations can save 27.4 % of the melting time at ε = 0.96. Therefore, it can be concluded that higher energy storage and melting rate can be achieved by increasing the number of undulations
  • No Thumbnail Available
    Item
    Investigation of the novelty of latent functionally thermal fluids as alternative to nanofluids in natural convective flows
    (Nature, 2020) Haddad, Zoubida; Iachachene, Farida; Abu-Nada, Eiyad; Ioan, Pop
    This paper presents a detailed comparison between the latent functionally thermal fluids (LFTFs) and nanofluids in terms of heat transfer enhancement. The problem used to carry the comparison is natural convection in a differentially heated cavity where LFTFs and nanofluids are considered the working fluids. The nanofluid mixture consists of Al2O3 nanoparticles and water, whereas the LFTF mixture consists of a suspension of nanoencapsulated phase change material (NEPCMs) in water. The thermophysical properties of the LFTFs are derived from available experimental data in literature. The NEPCMs consist of n-nonadecane as PCM and poly(styrene-co-methacrylic acid) as shell material for the encapsulation. Finite volume method is used to solve the governing equations of the LFTFs and the nanofluid. The computations covered a wide range of Rayleigh number, 104 ≤ Ra ≤ 107, and nanoparticle volume fraction ranging between 0 and 1.69%. It was found that the LFTFs give substantial heat transfer enhancement compared to nanofluids, where the maximum heat transfer enhancement of 13% was observed over nanofluids. Though the thermal conductivity of LFTFs was 15 times smaller than that of the base fluid, a significant enhancement in thermal conductivity was observed. This enhancement was attributed to the high latent heat of fusion of the LFTFs which increased the energy transport within the cavity and accordingly the thermal conductivity of the LFTFs.