Publications Internationales

Permanent URI for this collectionhttps://dspace.univ-boumerdes.dz/handle/123456789/13

Browse

Author: search.filters.author.Bezzazi, B.

Search Results

Now showing 1 - 10 of 23
  • No Thumbnail Available
    Item
    Study of rheological characteristics and mechanical strength properties of natural rubber vulcanizates varying the type and content of carbon black
    (ICAT, 2023) Kherbouche, Ahlem; Benidir, A.; Bezzazi, B.
    This paper presents a study about the influence of the size and content of two types of carbon black N220 and N550 with loading of 10–100 phr on the properties of the vulcanized natural rubber (NR). The mechanical characteristics such as the tensile strength, the tensile modulus, the elongation at break, the hardness, the abrasion resistance, and rheological properties of NR reinforced with carbon black were investigated. By analyzing the results of an N220 reinforced NR, the reinforcement gives improvement in tensile strengths when fillers are added up to 70 phr. However, and by referring to elongation at break, a fall of product elasticity is observed. The increase of filler loading results a decrease in rheological properties; optimum cure time, scorch time, cure rate index (CRI). Nevertheless, the N220 rubber compound exhibits slightly higher hardness than those registered for the N550 compounds. Regarding the mechanical properties under tensile stress, the engineer's findings are comparative for all the samples of the study. However, the rubber compound filled N220 or N550 gives comparable results on mechanical properties.
  • No Thumbnail Available
    Item
    Study of the Insecticidal Potential of Diatomaceous Earth from Sig (Algeria) on the Dermestes haemorrhoidalis - A Pest of Stored Food Product
    (2021) Djadi, Amina; Bouzid, Mohammed; Bezzazi, B.
    The insecticidal activity of the Diatomaceous Earth (DE) of Sig was assessed against the Dermestes haemorrhoidalis, which is the main pest affecting wheat stored in Blida, a central region of Algeria and one of the four cereal regions managed by the Algerian Inter-branch Cereals Office (AICO). The formulation was tested at two different doses: 500 and 1000 ppm against adults of the species. The bioassays were carried out in 1-litre glass jars containing soft wheat with an average moisture content of 60% mixed with diatomaceous earth and maintained at 27°C and 70% of humidity. The effectiveness of the treatment was assessed by recording adult mortality after 2, 7 and 14 days. Sig’s diatomite showed significant insecticidal activity against Dermestes haemorrhoidalis after only two days of treatment with both doses 500 and 1000 ppm. After 14 days, average mortality was more than 95% even at 500 ppm. Furthermore, electron microscopy of the diatomite particle from Sig (Algeria) reveals the architecture of the frustule. It shows a porous and brittle siliceous shell made largely of diatomite “skeletons”. This research work allowed getting insights into the mechanism of action of diatomite on the Dermestes haemorrhoidalis. On the other hand, the identification of diatomite of Sig was performed by X-ray diffraction and infrared.
  • No Thumbnail Available
    Item
    The effect of carbon black on the curing and mechanical properties of natural rubber/ acrylonitrile- butadiene rubber composites
    (Universidad Nacional Autonoma de Mexico, 2021) Boukfessa, Hind; Bezzazi, B.
    The present work investigates the effect of the amount of carbon black on curing and mechanical properties such as tensile strength, elongation at break, hardness and abrasion resistance of the natural rubber (NR)/ acrylonitrile-butadiene rubber (NBR) blend. For that purpose, a blend composed of 65% NR and 35% NBR filled with different content of carbon black N330 was used. The curing results indicate that the viscosity and the crosslink density of rubber composites increase and the scorch and curing times decrease with increasing the filler content. Mechanical properties such as tensile modulus and hardness of the CB filled NR/NBR blend were remarkably improved, indicating the inherent reinforcing potential of CB. Regarding tensile strength and abrasion resistance, they increase with the addition of carbon black, up to 50 phr. After that, these properties decrease slightly with filler addition
  • No Thumbnail Available
    Item
    Study and Physicochemical Characterization of the Diesel Particles Inducing Bronchopulmonary Obstructions and Inflammation
    (Technoscience Publications, 2021) Bouzid, Mohammed; Djadi, A.; Bezzazi, B.
    Micro-Visiography reveals that diesel soot particles are soluble in the physiological pulmonary liquid. It also shows that these substances stick to bronchial capillary walls. Electronic microscopy reveals structures of non-homogeneous morphology with spherical, fibrous and platelet-like structures. Analysis of the surfaces of the aggregates by Energy-dispersive X-ray microanalysis (EDX) shows the composition of chemical charges. Besides, X-ray diffraction and thermogravimetric study show the existence of two phases: Organic and crystalline, with a rubber elastomer aspect. Infrared and UV-Visible spectroscopic analysis confirmed the existence of reactive chemical groups
  • No Thumbnail Available
    Item
    Elaboration et caractérisation mécanique d’un matériau composite hybride
    (2006) Hachemane, B.; Mir, A.; Bezzazi, B.
  • No Thumbnail Available
    Item
    Quasi-static mechanical characterization and fatigue of a composite laminates
    (2014) Belkacemi, C.; Bezzazi, B.
    This present work focuses on the quasi- static mechanical characterization and or fatigue of a composite materials (laminate) jute/polyester manufactured under vacuum and with stacking sequences of 0/ 90. The obtained results of tensile tests on the laminate, showed a similar behavior on two levels: a linear portion up to 20 MPa and a nonlinear portion to rupture at 47 MPa σ max , followed by elongation of 2.08 % with a break elongation up to 2.50 %. Also, it was noted that increasing the temperature of the samples (5-6 ° C ) when the fatigue test remains in ISO 13003 , which requires a temperature increase of less than 10 ° C. the results of fatigue test showed also that with a loading of 50% of the maximum load reached more than one million cycle, the more load is increasing the cycle numbers of decreases
  • No Thumbnail Available
    Item
    Experimental study of sandwich multilayer reinforced by glass fibre and agglomerated cork
    (2014) Hami, Brahim; Irekti, Amar; Aribi, C.; Bezzazi, B.; Mir, A.
    This paper presents an experimental study which is determined the mechanical properties of a composite material sandwich multilayer developed in the laboratory of mechanics of materials and composites, Materials Research Unit, process and en¬vironment. This type of sandwich is composed of four layers laminated based on an epoxy resin reinforced by woven glass fibres and mast between which three plates of agglomerated cork with stacked alternately laminated layers. Specimens for bending tests three and four points were prepared from the multilayer sandwich panels. A first series of static three-point bending tests shows a clear difference in the fracture behaviour for materials, laminate and cork. These materials have undergone a large plastic deformation without rupture achieve full sandwich, with the onset of delamination between layers laminated material and cork. In order to determine the bending stiffness modules D, the shear modulus and flexural N and the shear modulus of the soul Ga, we conducted a second test campaign four points bending. As a result, we can develop a variety of white cork produced in Algeria in order to use it in the construction and automotive industries
  • No Thumbnail Available
    Item
    Study of the green composite Jute/Epoxy
    (2014) Mir, A.; Aribi, C.; Bezzazi, B.
    Work presented is interested in the characterization of the quasistatic mechanical properties and in fatigue of a composite laminated in jute/epoxy. The natural fibers offer promising prospects thanks to their interesting specific properties, because of their low density, but also with their bio-deterioration. Several scientific studies highlighted the good mechanical resistance of the vegetable fiber composites reinforced, even after several recycling. Because of the environmental standards that become increasingly severe, one attends the emergence of eco-materials at the base of natural fibers such as flax, bamboo, hemp, sisal, jute. The fatigue tests on elementary vegetable fibers show an increase of about 60% of the rigidity of elementary fibers of hemp subjected to cyclic loadings. In this study, the test-tubes manufactured by the method infusion have sequences of stacking of 0/90° and ± 45° for the shearing and tensile tests. The quasistatic tests reveal a variability of the mechanical properties of about 8%. The tensile fatigue tests were carried out for levels of constraints equivalent to half of the ultimate values of the composite. Once the fatigue tests carried out for well-defined values of cycles, a series of static tests of traction type highlights the influence of the number of cycles on the quasi-static mechanical behavior of the laminate jute/epoxy
  • No Thumbnail Available
    Item
    Study of mechanical and thermomechanical properties of jute/epoxy composite laminate
    (2010) Mir, A.; Zitoune, R.; Collombet, F.; Bezzazi, B.
    This article presents the development and the characterization of composite material (laminate) containing natural jute fiber reinforcement. Thermal characterization of jute fiber reinforcement shows the influence of the temperature on the mechanical behavior of fiber. At 180 C the jute fabric loses 50% of its mechanical characteristics. The laminate obtained by a process known as infusion is polymerized at a temperature lower than that which affects the mechanical properties of dry fabric. The digital image correlation carried out on laminated jute/epoxy (warp and weft direction) under tensile test shows the presence of a considerable gradient of deformation. This gradient is explained by the variability related to the local voluminal change of jute fibers of one place to the other and the nature of the weaving of the jute fiber. The three-point bending tests show a significant dispersion of rupture stress. The thermomechanical tests carried out on samples in the two principal directions, show that the thermal coefficient of expansion in warp direction is 48% larger compared to the weft direction. The thermogravimetric test shows that this laminate absorbs up to 4% water mass after 8 h in a climatic chamber with 70% moisture content
  • No Thumbnail Available
    Item
    Study of mechanical and hygrothermal properties of agglomerated cork
    (2012) Mir, A.; Bezzazi, B.; Zitoune, R.; Collombet, F.
    The mode of development of sandwich panels with cork core by the method infusion cannot prevent the resin from penetrating inside cork. This study characterizes white cork agglomerated before and after the development of sandwich panels to see the influence of the resin on the mechanical and hygrothermic characteristics of cork. Two types of cork are considered, they are characterized by their density of 270 kg/m3 (C270) and of 190 kg/m3 (C190). One notes that the modulus of rigidity of C270 cork is 20% larger than that of C190.The presence of resin increases also the module of shearing 47% for C270, 64% for C190. The hygrothermic analysis out of drying oven at 100°C shows a fall of significant mass in the first 7 hours. The analysis thermogravimetry at 220°C, the fall of significant mass is recorded in the first 5 minutes